Answer:
To run a spectrophotometry experiment, begin by warming up the spectrophotometer and preparing the samples. Be sure to select the correct wavelength, then run a measurement on the blank solution. Follow up by running measurements on sample solutions. Once data is collected, turn off the instrument, clean the area, and discard the samples.
Explanation:
The spectrophotometer is a device used in laboratories to carry out analysis in experiments that need to measure and compare the amount of light absorbed or transmitted between samples, regardless of whether the samples are transparent or opaque solid. The spectrophotometer can be single-beam and double-beam. Regardless of the nature of the beam, to perform a spectrophotometry experiment, you must start by heating the spectrophotometer and preparing the samples. Make sure to select the correct wavelength and perform a measurement on the blank solution. Follow up by performing measurements on sample solutions. Once the data is collected, turn off the instrument, clean the area and discard the samples.
20 Points!! Which of the following is a synthesis reaction? AgNO3+NaCI--> AgCI+NaNO3
CH4+O2->CO2+H2O SO3+H2O-> H2SO4 Cu+AgNO3 ->Ag+CuNO3
What animal has a see through body?
Describe the patterns and atomic mass is an ion charges in the periodic table
Answer:
The atomic number increases across a period and down the group or family. The atomic mass generally increases with atomic number with a few exceptions.
How many atoms are in 12 moles of sodium?
Answer: There are 1.20 x 1024 atoms of sodium in 2 moles
Explanation:
Which substances are released during cellular respiration?
Use complete sentences to explain how the mass of oxygen is conserved during cellular respiration.
A 14 year old girl is small in stature and appears younger than her age. She has not started menstruating, and her parents are concerned that she is not growing taller nor entering puberty. She has frequent headaches, and is having difficulty seeing the board at school, even though she sits near the front of the room. She feels cold, even when the room is warm, and she is often constipated. Her parents are concerned. She is in the 30th percentile for height and weight, significantly below her peers.
Required:
What hormones are of LEAST concern in this person?
a. insulin
b. GH
c. GnRH
d. TSH
Answer:
A.
B.
Explanation:
HELP ASAP PLS. Which of the following best describes the relationship between air temperature and relative humidity?
A. Cold air cannot hold any water vapor.
B. Warm air can hold less water vapor than cold air.
C. Cold air can hold less water vapor than warm air.
D. Warm air and water vapor are measured in degrees Celsius (⁰C).
Answer:
I think the answer might be C.
6. Which of the process would you use to remove salt
dissolved in water?
opicean .Filtration, evaporation, chlorination
Answer:
Evaporation
Explanation:
You can use evaporation to separate the salt from the water.
Is this answer correct
Answer:
Yes
Explanation:
The reaction for luminol is basically luminol and hydrogen peroxide. In the instructions for the preparation of the chemicals, I found that the hydrogen peroxide is 44 times more concentrated than the luminol. The fact that there are two reactants, should make you wonder if the reaction is second order overall. However, in class, we presented data that showed that the natural log of the amount of light change over time was a straight line with a negative slope. This would tend to make you think that the reaction is first order, given the information here, you can confidently say that this reaction is:
A. zeroth order
B. first order
C. pseudo first order
D. second order
E. third order
Answer:
pseudo first order
Explanation:
We know that for a first order reaction, the plot of the natural log of the amount of reactant against time is a straight line with a negative slope. In this case the amount of substance is monitored using the amount of light change. Hence, the plot of the natural log of the amount of light change against time was a straight line with a negative slope.
The statement above characterizes a first order reaction. However, we must remember that the reaction is bimolecular; it involves luminol and hydrogen peroxide. The hydrogen peroxide is 44 times more concentrated than the luminol making the reaction a pseudo first order reaction.
A Pseudo first-order reaction can be defined as a second-order or bimolecular reaction that is made to behave like a first-order reaction(Byjus).
Which of the following can be calculated from the mass of the reactants used in a chemical reaction? (Select all that apply)
Theoretical yield of products
Amount of limiting reactant used in a reaction
Actual yield of products
Amount of excess reactant from a reaction
Answer:
Can you explain it more please
Explanation:
Household hydrogen peroxide is an aqueous solution of hydrogen peroxide (H2O2), and its concentration is often measured as a percent by weight. Most drug stores sell 3% solution, which means there are 3.0 g of H2O2 per every 100 g total of solution (H2O2 H2O). For the kinetics experiment, 15 mL of 3% (w/w) hydrogen peroxide solution was poured into a measuring cup with 120 mL of water. 5 mL of 1M sodium carbonate solution (Na2CO3) was also added to the mixture. What is the molar concentration (molarity) of hydrogen peroxide (in mol/L) of the final solution
Answer:
0.093 M
Explanation:
First, we assume that the density of household hydrogen peroxide is 1 g/mL. We also assume that there's no reaction between hydrogen peroxide and sodium carbonate, if there were, in the end all hydrogen peroxide would be consumed.
Now we calculate how many grams of H₂O₂ were added, using the given volume, concentration and density:
15 mL * [tex]\frac{1gSolution}{1mL}*\frac{3gH_2O_2}{100gSolution}[/tex] = 0.45 g H₂O₂We convert grams to moles:
0.45 g H₂O₂ ÷ 34 g/mol = 0.013 mol H₂O₂
Now we divide the number of moles by the final volume, to calculate the molarity of H₂O₂:
Final Volume = 15 mL + 120 mL + 5 mL = 140 mL140 mL / 1000 = 0.140 LMolarity = 0.013 mol H₂O₂ / 0.140 L = 0.093 MBased on the given concentration of the original hydrogen peroxide solution, the molarity of the hydrogen peroxide (in mol/L) of the final solution is 0.093 M.
What is the concentration of the hydrogen peroxide solution?Assuming that the density of household hydrogen peroxide is 1 g/mL and that no reaction occurs between hydrogen peroxide and sodium carbonate.
The mass in grams of H₂O₂ added is first determined using the given volume, concentration and density:
mass = volume * density * concentrationmass = 15 mL * 1 g/mL * 3g/100g = 0.45 g H₂O₂
Moles of H₂O₂ is determined as follows:
moles = mass /molar massmolar mass of H₂O₂ = 34 g/mol
moles of H₂O₂ = 0.45 g H₂O₂ / 34 g/mol
moles of H₂O₂ = 0.013 mol H₂O₂
molarity of H₂O₂ is then calculated as follows:
molarity = moles/volume in Lfinal volume = 15 mL + 120 mL + 5 mL = 140 mL
final volume = 140 mL / 1000 = 0.140 L
molarity = 0.013 mol H₂O₂ / 0.140 L
molarity of H₂O₂ = 0.093 M
Therefore, the molarity of the hydrogen peroxide (in mol/L) of the final solution is 0.093 M.
Learn more about molarity at: https://brainly.com/question/17138838
Looking at the following equation, which is the correct order of coefficients?
NH3 + O2 --> NO + H2O
2NH3 + 302---> 2NO + 3H20
which planet in are solar system haves most moons
Answer:
Jupiter
Explanation:
HELP!!! TIMED! THANK YOU!
Answer:
The answer is A.
Explanation:
Answer:
Explanation:
I believe it is a
This is the chemical formula for the compound calcium chloride: CaCl2
In this compound, how many atoms are combined?
O1
02
O3
O4
Answer:
3
Explanation:
1 Calcium atom and two chlorine atoms
Should vaccinations be required for students to attend public school?
Answer:
I don't think so for now, there hasn't been much research done with the vaccine and children so we really don't know how children's bodies will react to it. Once more studies are done with the vaccine and children and is proven safe then yes, kids should use it in order to attend public school.
_______________ is the interaction between organisms in an ecosystem.
Convert Fahrenheit temperature
to Kelvin scales
Answer:
K = (F – 32)5/9 + 273.15
Explanation:
You basically convert Fahrenheit to Celcius and then to Kelvin
Here's the entire formula:
K = (x °F – 32)5/9 + 273.15
The vapor pressure of liquid octane, C8H18, is 40.0 mm Hg at 318 K. A sample of C8H18 is placed in a closed, evacuated container of constant volume at a temperature of 448 K. It is found that all of the C8H18 is in the vapor phase and that the pressure is 71.0 mm Hg. If the temperature in the container is reduced to 318 K, which of the following statements are correct?
a. The pressure in the container will be 42.8 mm Hg.
b. Liquid octane will be present.
c. Only octane vapor will be present.
d. Some of the vapor initially present will condense.
e. No condensation will occur.
Answer:
a, d
Explanation:
a. The pressure in the container will be 42.8 mm Hg.
d. Some of the vapor initially present will condense.
Arsenate (AsO43-) is structurally and chemically similar to inorganic phosphate (PO43-), and many enzymes that act on phosphate will also use arsenate as a substrate if it is available. However, unlike phosphates, organic compounds of arsenate are kinetically unstable. For example, acyl phosphates (such as 1,3-bisphosphoglycerate) require an enzyme to catalyze phosphate hydrolysis on a biologically relevant timescale, but acyl arsenates hydrolyze almost instantaneously in water without an enzyme.
a) Predict the effect on the net reaction catalyzed by glyceraldehyde 3-phosphate dehydrogenase if phosphate were replaced by arsenate.
b) Write a balanced overall equation for the conversion of glucose to pyruvate in the presence of ATP, ADP, NAD+, and arsenate.
c) Arsenate is extremely toxic to most organisms. Based on your answers above, explain why.
Answer:
A) The effect on the net reaction catalyzed by glyceraldehyde is that
The 1-arsen0, 3-phosphoglycerate will decompose without enzymes hence no ATP will be formed in the reaction ( phosphoglycerate Kinase )
B) There will be no conversion of ADP to ATP from the conversion of glucose to pyruvate hence No balanced overall equation can be derived
C ) Arsenate is very toxic to most organisms and it is used mostly regarded as poisons during the formation of glycolysis, it forms 1-arsen0, 3-phosphoglycerate which hinders the formation of ATP because it is unstable and will hydrolyze quickly, this will also lead to the reduction in oxygen in cells thereby leading to the death of cells
Explanation:
A) The effect on the net reaction catalyzed by glyceraldehyde is that
The 1-arsen0, 3-phosphoglycerate will decompose without enzymes hence no ATP will be formed in the reaction ( phosphoglycerate Kinase )
B) There will be no conversion of ADP to ATP from the conversion of glucose to pyruvate hence No balanced overall equation can be derived
C ) Arsenate is very toxic to most organisms and it is mostly regarded as poisons during the formation of glycolysis, it forms 1-arsen0, 3-phosphoglycerate which hinders the formation of ATP because it is unstable and will hydrolyze quickly, this will also lead to the reduction in oxygen in cells thereby leading to the death of cells
Those structures that are similar in all behavior is called homologous structure.
The answer of the following question is as follows:-
The effect on the net reaction catalyzed by glyceraldehyde is that the 1-arsen0, 3-phosphoglycerate will decompose without enzymes hence no ATP will be formed in the reaction ( phosphoglycerate Kinase ) There will be no conversion of ADP to ATP from the conversion of glucose to pyruvate hence No balanced overall equation can be derived Arsenate is very toxic to most organisms and it is used mostly regarded as a poison during the formation of glycolysis, it forms 1-arsen0, 3-phosphoglycerate which hinders the formation of ATP because it is unstable and will hydrolyze quickly, this will also lead to the reduction in oxygen in cells thereby leading to the death of a cell.For more information, refer to the link:-
https://brainly.com/question/15804584
3. What is an
electrolyte?
Answer:
An electrolyte is a substance that produces an electrically conducting solution when dissolved in a polar solvent, such as water. ... A substance that dissociates into ions in solution acquires the capacity to conduct electricity. Sodium, potassium, chloride, calcium, magnesium, and phosphate are examples of electrolytes.
Explanation:
Please give thanks to all my answers and please mark as brilliant and please follow me
How does a temperature increase cause the rate of a reaction to increase?
A. It increases the kinetic energy of the molecules.
B. It decreases orientation requirements of the molecules.
C. It increases the equilibrium constant for the reaction.
D. It decreases the activation energy of the reaction.
Answer:
B
Explanation:
"The temperature increases cause the rate of a reaction to increases the kinetic energy"
What is rate of reaction?
The reaction rate, also known as the rate of reaction, is the rate for which a chemical reaction occurs, and is proportional to increase in product concentration per unit time and the reduction in reactant concentration per unit time. The rate of reaction varies greatly.
What is kinetic energy?
An object's kinetic energy is the energy it has as a result of its motion. It is the amount of work required to push a body of a given mass from rest to a certain velocity. The body keeps its kinetic energy gained during acceleration unless that speed changes.
To know more about rate of reaction click here.
https://brainly.com/question/3334857.
#SPJ2
A compound X has the following percentage composition 66.7% carbon, 11.1% hydrogen and 22.2% oxygen .Calculate the empirical formula of X.The relative molecular mass of X is 72 calculate the molecular formula
Explanation:
c. h. o
66.7%. 11.1%. 22.2%
____. ____. ____
12. 1. 16
1.558. 11.1. 1.39. (divide by the smallest)
1. 8. 1
empirical formula=ch8o
Carbon monoxide is a colorless, odorless gas that binds irreversibly to hemoglobin in our blood, causing suffocation and death. CO is formed during incomplete combustion of carbon. One way to represent this equilibrium is: CO(g)C(s) 1/2 O2(g) We could also write this reaction three other ways, listed below. The equilibrium constants for all of the reactions are related. Write the equilibrium constant for each new reaction in terms of K, the equilibrium constant for the reaction above.
The question is missing some parts. Here is the complete question.
Carbon monoxide is a colorless, odorless gas that binds irreversibly to hemoglobin in our blood, causing suffocation and death. CO is formed during incomplete combustion of carbon. One way to represent this equilibrium is:
[tex]2CO_{(g)}[/tex] ⇄ [tex]2C_{(s)}+O_{2}_{(g)}[/tex]
we could also write this reaction three other ways listed below. The equilibrium constant for all of the reactions are related. Write the equilibrium constant for each new reaction in terms of K, the equilibrium constant for the reaction above.
1) [tex]2C_{(s)}+O_{2}_{(g)}[/tex] ⇄ [tex]2CO_{(g)}[/tex] K₁ =
2) [tex]C_{(s)}+1/2O_{2}_{(g)}[/tex] ⇄ [tex]CO_{(g)}[/tex] K₂ =
3) [tex]CO_{(g)}[/tex] ⇄ [tex]C_{(s)}+1/2O_{2}_{(g)}[/tex] K₃ =
Answer: 1) [tex]K_{1}=\frac{1}{K}[/tex]
2) [tex]K_{2}=\frac{1}{K^{1/2}}[/tex]
3) [tex]K_{3}=K^{1/2}[/tex]
Explanation: A chemical reaction can be reversible, i.e., can proceed in both directions: to the right of the arrow (forward) or towards the left of the arrow (backward).
When the rates of forward and backward reactions are the same, the reaction is in equilibrium. In that state, we can determine the equilibrium constant, [tex]K_{c}[/tex].
For the first way to represent equilibrium of CO formed, the [tex]K_{c}[/tex] is calculated
[tex]2CO_{(g)}[/tex] ⇄ [tex]2C_{(s)}+O_{2}_{(g)}[/tex]
[tex]K=\frac{[O_{2}]}{[CO]^{2}}[/tex]
in which the symbol [ ] is concentration of the compound.
In equilibrium constant, solids are not included.
Equilibrium constants for the other reactions:
1) [tex]2C_{(s)}+O_{2}_{(g)}[/tex] ⇄ [tex]2CO_{(g)}[/tex]
[tex]K_{1}=\frac{[CO]^{2}}{[O_{2}]}[/tex]
Comparing K₁ and K, the first one is the inverse of K, so writing in terms of K
[tex]K_{1}=\frac{1}{K}[/tex]
2) [tex]C_{(s)}+1/2O_{2}_{(g)}[/tex] ⇄ [tex]CO_{(g)}[/tex]
[tex]K_{2}=\frac{[CO]}{[O_{2}]^{1/2}}[/tex]
In terms of K, K₂ is
[tex]K_{2}=\frac{1}{K^{1/2}}[/tex]
3) [tex]CO_{(g)}[/tex] ⇄ [tex]C_{(s)}+1/2O_{2}_{(g)}[/tex]
[tex]K_{3}=\frac{[O_{2}]^{1/2}}{[CO]}[/tex]
This constant in terms of K will be
[tex]K_{3}=K^{1/2}[/tex]
In conclusion, K₁, K₂ and K₃ in terms of K is [tex]\frac{1}{K}[/tex],[tex]\frac{1}{K^{1/2}}[/tex] and [tex]K^{1/2}[/tex], respectively.
How does fertilizer benefit the daily lives of people?
Answer:
Fertilizers play an important role in providing crops with the nutrients they need to grow and be harvested for nutritious food. Fertilizers help deliver enough food to feed the world's population. ...
For example, micronutrients such as zinc are important to human nutrition, especially children.
Explanation:
Hope it is helpful.....
Please help me answer this I will mark brainliest
Answer:
A is brain, ND the fact that u don't know this stuff is a lil bit sad, u can so look it
Explanation:
What is the volume of 0.05 mol of neon gas at 1.45 atm and 275K?
Answer:
sdasdasddsafsadsfds
Explanation:
In the compound aluminum oxide, which is the cation?
Answer:
-Aluminum Oxide: The cation is Al3+ and the anion is O2-. The sum of the charges for aluminum oxide is 2(3+) + 3(2-) = 0. Thus, the formula is Al2O3. An ionic compound is named using the name of the cation followed by the name of the anion, eliminating the word ion from each.
Explanation:
A sample of 523.1 mg of impure KBr is treated with an excess of AgNO3 and 814.5 mg of AgBr is obtained. What is the purity of KBr?
Answer:
98.68%
Explanation:
Step 1: Write the balanced equation
KBr + AgNO₃ ⇒ AgBr + KNO₃
Step 2: Calculate the moles corresponding to 814.5 mg (0.8145 g) of AgBr
The molar mass of AgBr is 187.77 g/mol.
0.8145 g × 1 mol/187.77 g = 4.338 × 10⁻³ mol
Step 3: Calculate the moles of KBr needed to produce 4.338 × 10⁻³ moles of AgBr
The molar ratio of KBr to AgBr is 1:1. The moles of KBr needed are 1/1 × 4.338 × 10⁻³ mol = 4.338 × 10⁻³ mol.
Step 4: Calculate the pure mass corresponding to 4.338 × 10⁻³ moles of KBr
The molar mass of KBr is 119.00 g/mol.
4.338 × 10⁻³ mol × 119.00 g/mol = 0.5162 g
Step 5: Calculate the purity of KBr
0.5162 g of KBr are in a 0.5231 g-sample. The purity of KBr is:
P = 0.5162 g/0.5231 g × 100% = 98.68%