Answer:
An earthquake could occur.
Answer:
The correct answer is (lava)
Explanation:
Youre welcome
When the plates move they collide or spread apart allowing the very hot molten material called lava to escape from the mantle. When collisions occur they produce mountains, deep underwater valleys called trenches, and volcanoes.
What size volumetric flask would you use to create a 0.50 M
solution using 10.00 g of CaBr2
Answer:
Explanation:
First convert the grams of Calcium Bromide to moles by using the atomic weight. Then use the formula for molarity, which is moles per liter.
CaBr2 = 199.9 g/mol
10/199.9 = 0.05 moles of CaBr2
[tex]0.5M=\frac{0.05mol}{x}[/tex]
x = 0.1L or 100mL
Looking at the following equation, which is the correct order of coefficients?
NH3 + O2 --> NO + H2O
2NH3 + 302---> 2NO + 3H20
In order to dissolve a chemical sample in a recrystallization solvent, add the room-temperature solvent ___________ in an Erlenmeyer flask on a hot plate. Turn on the heat, starting at __________________. Using a _______, add additional solvent from a second container on the heat source. Swirl the sample flask after each addition, and try to add _______________ in order to dissolve the solid.
Answer:
just until it covers the sample
a low setting and increasing gradually
pipet
as little solvent as possible
Explanation:
In order to dissolve a chemical sample in a recrystallization solvent, add the room-temperature solvent just until it covers the sample in an Erlenmeyer flask on a hot plate. Turn on the heat, starting at a low setting and increasing gradually. Using a pipet, add additional solvent from a second container on the heat source. Swirl the sample flask after each addition, and try to add as little solvent as possible in order to dissolve the solid.
What is an oceanographer likely to find in a typical sample of salt water from the
ocean floor?
Water with high salt content, low in temperature, and low in density.
Water with average salt content, high in temperature, and high in density.
Water with high salt content, high in temperature, and high in density.
Water with high salt content, low in temperature, and high in density.
Explanation:
the oceanographic is likely to find water with high salt content, low in temperature and high in density
Water with high salt content, low in temperature, and high in density likely to find in a typical sample of salt water from the ocean floor. Therefore, the correct option is option D.
What is an oceanography?Oceanography, also known as oceanology as well as ocean science, is indeed the scientific paper of the seas. The term is derived from the Ancient Greek words "ocean" (v) and "writing" (graph), respectively.
Geophysical fluid dynamics, plate tectonics, the geology of the ocean floor, and fluxes of different chemical compounds and physical qualities both inside and across the ocean are all factors that affect waves and ocean currents. Water with high salt content, low in temperature, and high in density likely to find in a typical sample of salt water from the ocean floor.
Therefore, the correct option is option D.
To know more about oceanography, here:
https://brainly.com/question/13276902
#SPJ5
What animal has a see through body?
Ve. In what layer do weather balloons fly?
Earth layers
Answer:
stratosphere
Explanation:
What is the volume of 0.05 mol of neon gas at 1.45 atm and 275K?
Answer:
sdasdasddsafsadsfds
Explanation:
nitrophenol is more acidic than phenol.
Answer:
The p- nitrophenol is more acidic than phenol because the deactivating nature of nitro group and after loosing the protons it makes more resonance stabilization as nitro group is having strong deactivating nature so it attracts electrons towards it.
In the periodic table what is the 65th element? (pls help me)
Answer:
Terbium
Explanation:
All elements are put in squares on the periodic table. They represent the number of protons in the nucleus. They are the largest number in the square. The elements go up in order. Number 65 is in the row following Calcium. It is about in the middle of that row.Danielle is designing a system to help race cars slow safely and rapidly at her local racetrack. The racetrack is a straight, 1,000-meter stretch of asphalt. Half of the track is devoted to races and the other half is designed to let cars decelerate after crossing the finish line.
Danielle has designed a pair of small parachutes that are automatically released out the back of a car once it crosses the finish line. When her system works properly, the race car driver does not need to apply the brakes to bring the car to a stop before running out of track.
When Danielle tests a prototype of her design, it brings a race car to a stop 275 meters behind the finish line. After taking some measurements, she decides that her design causes the driver to experience too much force. To correct this, she could
A.
make the parachutes larger in order to increase the drag forces on the car and bring it to a stop 200 meters after crossing the finish line.
B.
add a third parachute in order to increase the drag forces on the car and bring it to a stop 175 meters after crossing the finish line.
C.
make the parachutes smaller in order to decrease the drag forces on the car and bring it to a stop 400 meters after crossing the finish line.
D.
remove one of the parachutes in order to decrease the drag forces on the car and bring it to a stop 550 meters after crossing the finish line.
Answer:
The answer is C
Explanation:
She should make the parachutes smaller in order to decrease the drag forces on the car and bring it to a stop 400 meters after crossing the finish line.
read carefully and do this questions all part all questions if someone do this questions I will make you brainly and give you thanks.
Answer:
2a. Calcium chloride
2b.hydrochloride acid
2c. water molecules
2d.hydrochloric acid
2e.carbon dioxide
Explanation:
CaCO3+2HCl＝CaCl2+CO2+H2O
What does it mean for heat to be transferred by thermal conduction?
Answer:
thermal energy
Explanation:
Thermal conduction is the diffusion of thermal energy (heat) within one material or between materials in contact. The higher temperature object has molecules with more kinetic energy; collisions between molecules distributions this kinetic energy until an object has the same thermal energy throughout.
Answer:
energy is transferred when one molecule collides with another.
Explanation:
aP33x
What is geberal formula for alkane?
Answer:
CnH2n+2
Explanation:
Alkane have double and two atoms of hydrogen than carbon atoms
Like C4H10
n = 4
CnH2n+2
C4H2×4+2
C4H10
what is the molarity of ethanol c2h5oh in an aqueous solution that is 36.4% ethanol by mass
Answer:
the answer is A
Explanation:
Explain three types eye protection and their appropriate uses
Answer:
safety glasses, safety goggles, face shield, they protect your eyes from harmful liquids, bright lights
As illustrated, the below manometer consists of a gas vessel and an open-ended U-tube containing a nonvolatile liquid with a density of 0.993 g/mL. The difference in heights of the liquid in the two sides of the manometer is 32.3mm when the atmospheric pressure is 765 mm Hg. Given that the density of mercury is 13.6 g/mL, the pressure of the enclosed gas is ________ atm. Group of answer choices
Answer:
1.01atm is the pressure of the gas
Explanation:
The difference in heights in the two sides is because of the difference in pressure of the enclosed gas and the atmospheric pressure. This difference is in mm of the nonvolatile liquid. The difference in mm Hg is:
32.3mm * (0.993g/mL / 13.6g/mL) = 2.36mmHg
As atmospheric pressure is 765mm Hg and assuming the gas has more pressure than the atmospheric pressure (There is no illustration), the pressure of the gas is:
765mm Hg + 2.36mm Hg = 767.36 mmHg
In atm:
767.36 mmHg * (1atm / 760 mmHg) =
1.01atm is the pressure of the gas
Given:
Density of mercury = 13.6 g/mLDensity of nonvolatile liquid = 0.993 g/mLDifference in height = 32.3mmAtmospheric pressure = 765 mm HgNow,
The density of Hg will be:
= [tex]\frac{13.6}{0.791}[/tex]
= [tex]17.2 \ mm[/tex]
then,
= [tex]32.3\times (\frac{1 \ mm \ Hg}{17.2} )[/tex]
= [tex]18.73 \ mm \ Hg[/tex]
hence,
The pressure will be:
= [tex]765-18.73[/tex]
= [tex]746.27 \ mm \ Hg[/tex]
= [tex]0.993 \ atm[/tex]
Thus the above answer is right.
Learn more about gas vessel here:
https://brainly.com/question/7205294
Question 9 a N20(9) + CO(9) - N2(9) + CO2(9) The rate of the reaction represented above increases significantly in the presence of Pd(s). Which of the following best explains this observation?
А Pd increases the activation energy of the reaction.
B Pd absorbs the heat produced in the reaction. C One of the reactants binds on the surface of Pd, which introduces an alternative reaction pathway with a lower activation energy.
D One of the products binds on the surface of Pd, which increases the reaction rate by decreasing the concentration of products in the mixture.
Answer:
Ans choise B
Explanation:
Increasing rates of reaction by catalysts always results because of decrease in activation energy occurs.
How does a temperature increase cause the rate of a reaction to increase?
A. It increases the kinetic energy of the molecules.
B. It decreases orientation requirements of the molecules.
C. It increases the equilibrium constant for the reaction.
D. It decreases the activation energy of the reaction.
Answer:
B
Explanation:
"The temperature increases cause the rate of a reaction to increases the kinetic energy"
What is rate of reaction?
The reaction rate, also known as the rate of reaction, is the rate for which a chemical reaction occurs, and is proportional to increase in product concentration per unit time and the reduction in reactant concentration per unit time. The rate of reaction varies greatly.
What is kinetic energy?
An object's kinetic energy is the energy it has as a result of its motion. It is the amount of work required to push a body of a given mass from rest to a certain velocity. The body keeps its kinetic energy gained during acceleration unless that speed changes.
To know more about rate of reaction click here.
https://brainly.com/question/3334857.
#SPJ2
Which statement best explains how the solution should be made?
A) Add 1.5 mL of 0.50 M H2SO4 to 10.5 mL of water to get 12 mL of 4 M H2SO4.
B) Add 1.5 mL of 4.00 M H2SO4 to 10.5 mL of water to get 12 mL of 0.50 M H2SO4.
C) Add 1.5 mL of 4.00 M H2SO4 to 12 mL of water to get 0.50 M H2SO4.
Answer:
B
Explanation:
Correct on Edge
write the chemical equation of the reaction with a change in colour
Answer:
(i) Change in colour (ii) Change in temperature (iii) Formation of precipitate
Explanation:
(i) Change in colour: Reaction between lead nitrate solution and potassium iodide solution. Pb(NO3)2(aq)+2KI → PbI2(s)+2KNO3(aq) In this reaction, colour changes from colourless to yellow. (ii)Change in temperature: Action of dilute sulphuric acid on zinc. Zn(s) + H2SO4(aq) → ZnSO4(aq) + H2 In this reaction, heat is evolved (iii) Formation of precipitate: Action of barium chloride on sodium sulphate. BaCl2(aq) +Na2SO4(aq) → BaSO4(s) +2NaCl(aq) BaSO4(s)
Connor turns on a hair dryer to style his hair in the morning. Which choice identifies all of the energy transformations in the system?
electrical -- heat sound, and motion
electrical -- sound and motion
heat-electrical and sound
heat and sound -motion
Answer:
It is electrical → heat, sound, and motion
because a hair dryer makes heat to dry your hair and sound is the blowing and motion is how it goes
Explanation:
Answer:
A
Explanation:
electrical -- heat sound, and motion
of nitrogen gas)?
How many grams of H2 are needed to produce 71.1 g of ammonia (NH3) (assuming unlimited availability
3 H2+ N2 + 2NH3
Provide the answer with 3 or more significant figures.
Answer:
[tex]m_{H_2}=12.6gH_2[/tex]
Explanation:
Hello there!
In this case, given the reaction:
[tex]3 H_2+ N_2 \rightarrow 2NH_3[/tex]
It is possible to compute the necessary grams of hydrogen which produce 71.1 g of ammonia, given the 3:2 mole ratio and their molar mass as shown below:
[tex]m_{H_2}=71.1gNH_3*\frac{1molNH_3}{17.04gNH_3}*\frac{3molH_2}{2molNH_3} *\frac{2.02gH_2}{1molH_2}\\\\m_{H_2}=12.6gH_2[/tex]
Best regards!
A) Calculate the vapor pressure of a 7% by mass benzaoic acid in ethanol solution at 30°C. The vapor pressure of pure ethanol at this temperature is 13.40 kPa. ( assume a 100 g of solution)
B) Calculate the boiling point of the solution above
Answer:
the answer is C
Explanation:
Definition of chemical change
Answer:
Chemical changes occur when a substance combines with another to form a new substance, called chemical synthesis or, alternatively, chemical decomposition into two or more different substances. These processes are called chemical reactions and, in general, are not reversible except by further chemical reactions.
Explanation:
In fossil comparisons, it helps to know about similar:
living things
questions
incomplete remains
Answer:
Fossils tell us when organisms lived, as well as provide evidence for the Fossils are the preserved remains or traces of animals, plants, and other organisms from the past. Fossils, by comparing the anatomies of both modern and extinct species, allows scientists to study the skin, hair, and organs of ancient creatures.
Explanation:
IUPAC name for c2h2cl2?
Answer:
okay that is cool
Explanation:
Answer:
I hope it helps u! :)
Explanation:
Which two notations represent isotopes of the same element?
1.
N and EN
2.
N and Ne
3
N and Ne
4.
N and Ne
Submit Answer
Answer:
No.2, No.3 and No.4 answers are same. Give the options properly.
According to the tow of conservation of matter, we know that the total number of atoms does not change in a chemical reaction and thus mas is conserved This
is part of a chemical reaction hydrogen plus orygon yobis water Can you complete this moder? Reorganize the reactants in order to complete the productie
of the reaction
Your answer:
Answer:
no sé de eso perdón necesito los puntos
where do coal,oil and natural gas came from?
Answer:
I hope it will help you
plz mark me as brainliest
plz thank my answer
3. What is an
electrolyte?
Answer:
An electrolyte is a substance that produces an electrically conducting solution when dissolved in a polar solvent, such as water. ... A substance that dissociates into ions in solution acquires the capacity to conduct electricity. Sodium, potassium, chloride, calcium, magnesium, and phosphate are examples of electrolytes.
Explanation:
Please give thanks to all my answers and please mark as brilliant and please follow me