Answer: 0 I think
Explanation:
pretty sure its zero because i learned it last year but im in middle school so you might want to look it up.
why are copper pipes used in place of old lead pipes for plumbing systems?
iron (III) oxide pentahydrate formula
Answer:
Molecular Formula Fe2O12S3·5H2O
IUPAC Name iron(3+);tri sulfate;pentahydrate
Explanation:
calculate the equilibrium concentration for the nonionized bases and all ions in a solution that is 0.25M
Answer:
The equilibrium concentration of [CH₃NH₂] = 0.23965 M.
The equilibrium concentration of CH₃NH₃⁺ and OH⁻ = 0.01035 M respectively.
Explanation:
The first step is to write out the dissociation reaction. Therefore, the equation showing the dissociation is given as below;
CH₃NH₂ + H₂0 <--------------------------------------------------------> CH₃NH₃⁺ + OH⁻.
Kindly note that ''<----------->'' arrow shows that the reaction is an equilibrium reaction.
Therefore, at the start of the reaction [that is time, t =0], we have that the concentration of CH₃NH₂ = 0.25M, thus, the concentration of CH₃NH₃⁺ and OH⁻ is zero respectively at this time, t =0.
At equilibrium, the concentration of CH₃NH₂ = 0.25M - x, thus, the concentration of CH₃NH₃⁺ and OH⁻ is x respectively.
Therefore, kb = 4.47 × 10-4 = [CH₃NH₃⁺ ][OH⁻]/[CH₃NH₂]. Hence, slotting in the values into this equilibrium equation showing the relationship between kb and concentration of the species involved, we have that;
kb = 4.47 × 10⁻⁴ = x² /0.25 - x.
x² + 4.47 × 10⁻⁴x - 1.1175 × 10⁻⁴ = 0.
Solving this quadratic equation gives us the value of x as 0.01035 M.
Thus, the concentration of [CH₃NH₂] = 0.25 M - 0.01035 M = 0.23965 M
The equilibrium concentration of [CH₃NH₂] = 0.23965 M.
The equilibrium concentration of CH₃NH₃⁺ and OH⁻ = 0.01035 M respectively.
4. This is low wet land.
A. swamp
B. island
C. desert
D. peninsula
5. Japan is one of these.
A. island
B. peninsula
C. swamp
D. desert
Answer:
swap
Explanation: because it is a low wet land
Answer:
4. swamp
5. Island
Plz mark brainliest:)
A chemical engineer must calculate the maximum safe operating temperature of a high-pressure gas reaction vessel. The vessel is a stainless-steel cylinder that measures 41.0cm wide and 49.2cm high. The maximum safe pressure inside the vessel has been measured to be 3.70MPa. For a certain reaction the vessel may contain up to 2.50kg of dinitrogen difluoride gas.
Required:
Calculate the maximum safe operating temperature the engineer should recommend for this reaction. Write your answer in degrees Celsius. Be sure your answer has the correct number of significant digits.
Answer:
[tex]T=2.78x10^3 \°C[/tex]
Explanation:
Hello,
In this case, considering that the safe temperature may be computed via the ideal gas law as we now the pressure, mass and volume via the dimensions:
[tex]V=\pi r^2 h=\pi *(41.0cm)^2*49.2cm=2.60x10^5cm^3*\frac{1L}{1000cm^3} =260L[/tex]
The pressure in atm is:
[tex]P=3.70MPa*\frac{1x10^6Pa}{1MPa} \frac{1atm}{101325Pa} =36.5atm[/tex]
And the moles considering the mass and molar mass (66 g/mol) of dinitrogen difluoride (N₂F₂):
[tex]n_{N_2F_2}=2.50kg*\frac{1000g}{1kg}*\frac{1mol}{66g} =37.9mol[/tex]
In sich a way, by applying the ideal gas equation, which is not the best assumption but could work as an approximation due to the high temperature, the temperature, with three significant figures, will be:
[tex]T=\frac{PV}{nR}=\frac{36.5Pa*260L}{37.9mol*0.082\frac{atm*L}{mol*K} }\\ \\T=3053.6K-273.15\\\\T=2.78x10^3 \°C[/tex]
Best regards.
Use the periodic table to identify the chemical symbol or name for each element below.
zirconium:
zr
rhenium:
re
: As
: K
tin:
yttrium:
: Yb
Answer:
zirconium is Zr
rhenium is Re
As is arsenic
K is potassium
tin is Sn
yttrium is Y
ytterbium is Yb
Explanation:
With the help of the periodic table, the identification of the chemical symbol or name for each element is represented as follows:
Zirconium: Zr. Rhenium: Re. Arsenic: As.Potassium: K.Tin: Sn. Yttrium: Y. Ytterbium: Yb. What are the chemical elements?Chemical elements may be defined as any type of substance that cannot be further decomposed into simpler substances through the utilization of other ordinary chemical processes or external factors. These elements possess specific physical as well as chemical properties distinctly.
In the modern periodic table, each element is arranged on the basis of its increasing atomic number. Each element possesses its unique symbol, atomic mass, and physical properties like boiling points, melting points, density, etc.
Therefore, with the help of the periodic table, the identification of the chemical symbol or name for each element is well represented above.
To learn more about the Periodic table, refer to the link:
https://brainly.com/question/15987580
#SPJ2
How many moles of precipitate will be formed when 100.0 mL of 0.200 M NaBr is reacted with excess Pb(NO₃)₂ in the following chemical reaction?
2 NaBr (aq) + Pb(NO₃)₂ (aq) → PbBr₂ (s) + 2 NaNO₃ (aq)
Answer : The number of moles of precipitate, [tex]PbBr_2[/tex] formed will be 0.01 moles.
Explanation : Given,
Concentration of NaBr = 0.200 M
Volume of solution = 100.0 mL = 0.1 L (1 L = 1000 mL)
First we have to calculate the moles of NaBr.
[tex]\text{Moles of NaBr}=\text{Concentration of NaBr}\times \text{Volume of solution in L}[/tex]
[tex]\text{Moles of NaBr}=0.200M\times 0.1L=0.02mol[/tex]
Now we have to calculate the moles of precipitate, [tex]PbBr_2[/tex] formed.
The balanced chemical reaction is:
[tex]2NaBr(aq)+Pb(NO_3)_2(aq)\rightarrow PbBr_2(s)+2NaNO_3(aq)[/tex]
From the balanced chemical reaction we conclude that:
As, 2 moles of NaBr react to give 1 mole of [tex]PbBr_2[/tex]
So, 0.02 moles of NaBr react to give [tex]\frac{0.02}{2}=0.01[/tex] mole of [tex]PbBr_2[/tex]
Therefore, the number of moles of precipitate, [tex]PbBr_2[/tex] formed will be 0.01 moles.
The number of mole of the precipitate (i.e PbBr₂) formed when 100 mL of 0.2 M NaBr react with excess Pb(NO₃)₂ is 0.01 mole
We'll begin by calculating the number of mole of NaBr in 100 mL of 0.2 M NaBr solution. This can be obtained as follow:Volume = 100 mL = 100 / 1000 = 0.1 L
Molarity of NaBr = 0.2 M
Mole of NaBr =?Mole = Molarity x Volume
Mole of NaBr = 0.2 × 0.1
Mole of NaBr = 0.02 mole Finally, we shall determine the number of mole of the precipitate (i.e PbBr₂) produced from the reaction. This can be obtained as follow:2NaBr(aq) + Pb(NO₃)₂(aq) → PbBr₂(s) + 2NaNO₃ (aq)
From the balanced equation above,
2 moles of NaBr reacted to produce 1 mole of PbBr₂.
Therefore,
0.02 mole of NaBr will react to produce = [tex]\frac{0.02}{2} \\\\[/tex] = 0.01 mole of PbBr₂.
Thus, the number of mole of the precipitate (i.e PbBr₂) produced from the reaction is 0.01 mole
Learn more: https://brainly.com/question/19572703
List the steps in the water cycle, in the correct order?
Calculate the sublimation pressure of the solid at the melting point of 400.00 K assuming that the enthalpy of sublimation is not a function of temperature.
This question is incomplete, the complete question is;
Tonksite is a solid at 300.00K. At 300.00 K its enthalpy of sublimation is 66.00 kJ/mol. The sublimation pressure at 300.00 K is 5.00 × 10⁻⁴ atm
Calculate the sublimation pressure of the solid at the melting point of 400.00 K assuming that the enthalpy of sublimation is not a function of temperature.
Answer: the sublimation pressure of the solid at the melting point is 0.3727 atm
Explanation:
Given that;
T1 = 300 K
T2 = 400 K
H_sub = 66 kJ/mol = 66000 J/mol
P1 = 5.00 × 10⁻⁴ atm
p2 = ?
now using the expression
log( p2 / 5.00 × 10⁻⁴ ) = (H_sub / R × 2.303 ) (( T2 - T1) / T1T2)
now we substitute of given values into the expression
log(p2/p1) = (66000 / 8.314 × 2.303 ) (( 400 - 300) / 300 × 400 )
p2 = 0.3727 atm
therefore the sublimation pressure of the solid at the melting point is 0.3727 atm
A sample of an ideal gas has a volume of 2.23 L at 289 K and 1.05 atm. Calculate the pressure when the volume is 1.08 L and the temperature is 304 K. P= atm
Answer:
2.28 atm
Explanation:
V₁ = 2.33L, V₂ = 1.08L
T₁ = 289K, T₂ = 304K
P₁ = 1.05 atm, P₂ = ?
Where V₁ and V₂ are initial and final volume respectively
T₁ and T₂ are initial and final temperature respectively
P₁ and P₂ are initial and final pressure respectively
The formula to be used here is the general gas equation:
P₁V₁/T₁=P₂V₂/T₂
1.05 × 2.23/289 = P₂ × 1.08/304
P₂ × 1.08 × 289 = 1.05 × 2.23 × 304
P₂ = (1.05 × 2.23 ×304) ÷ (1.08 × 289)
P₂ = 711.82 ÷ 312.12
P₂ = 2.28 atm
Answer each of the following questions with increases, decreases, or does not change.
a) If the intermolecular forces in a liquid increase, the normal boiling point of the liquid increases .
b) If the intermolecular forces in a liquid increase, the vapor pressure of the liquid does not change .
c) If the surface area of a liquid increases, the vapor pressure increases .
d) If the temperature of a liquid decreases, the equilibrium vapor pressure increases .
Drag and drop your selection from the following list to complete the answer:
does not change decreases increases
Answer:
1) Increases
2) decreases
3) increases
4) decreases
Explanation:
When the intermolecular forces in a liquid increases, the greater vapour pressure of the liquid decreases accordingly.
Since the vapour pressure is proportional to temperature, as temperature increases, the vapour pressure increases alongside.
As intermolecular forces increases, the boiling point increases accordingly since more energy is required to break intermolecular bonds.
Lastly, the greater the surface area, tell greater the vapour pressure since more liquid surface area is now available.
Calculate the density of the aluminum cylinder with a diameter 0f 1.3 cm weighing 18 grams. Height of the cylinder is 5.2 Cm. Find percent error (Actual density of Aluminum is 2.7 g/cm3). (Formula for volume of cylinder is πr2h)
Answer:
Percent error = 3.7%
Explanation:
Given data:
Density of Al cylinder = ?
Weight of cylinder = 18 g
Diameter = 1.3 cm
Height = 5.2 cm
Actual density of Al = 2.7 g/cm³
Percent error = ?
Solution:
First of all we will calculate the volume of cylinder through given formula.
V = πr²h
r = diameter /2
V = 22/7 × (0.65 cm)²× 5.2 cm
V = 22/7 × 0.4225cm²× 5.2 cm
V = 6.89 cm³
Now we will calculate the density.
d = m/v
d = 18 g/ 6.89 cm³
d = 2.6 g/cm³
Percent error:
Percent error = measured value - actual value /actual value × 100
Percent error = 2.6g/cm³ - 2.7g/cm³ /2.7g/cm³ × 100
Percent error = 3.7%
Negative sign shows that measured or experimental value is less than actual value.
using this chemical might discolour equipment and surfaces
Answer: do not know how to answer this
Explanation:
Which of the following molecules may show a pure rotational microwave absorption spectrum: (i) H2, (ii) HCl, (iii) CH4, (iv) CH3Cl, (v) CH2Cl2?
Answer:
Explanation:
H₂ , HCl , CH₃Cl , CH₂Cl₂ ---- Yes
CH₄ ------ No .
Symmetric molecules do not have rotational microwave absorption spectrum because they do not possess permanent dipole moment so they lack polarisability .
The pure rotational microwave absorption spectrum has been possessed by HCl and [tex]\rm \bold{CH_3Cl}[/tex].
Pure rotational microwave absorption has been consisted of the molecules having dipole and polarizability. The molecules that show the spectrum and dipole are diatomic molecules, linear molecules, spherical molecules.
(i) The hydrogen has been a diatomic molecule with symmetry thus not showing a pure rotational microwave absorption spectrum.
(ii) The HCl being a linear molecule possesses a pure rotational microwave absorption spectrum.
(iii) [tex]\rm CH_4[/tex] molecule has symmetry, thus will not possess a pure rotational microwave absorption spectrum.
(iv) [tex]\rm CH_3Cl[/tex] molecule has no symmetry, and thus possesses a pure rotational microwave absorption spectrum.
(v) [tex]\rm CH_2Cl_2[/tex] molecule with the presence of symmetry, thus lacks a pure rotational microwave absorption spectrum.
For more information about the pure rotational microwave absorption spectrum, refer to the link:
https://brainly.com/question/14215380
The energy associated with the motion and position of an object is called a.kinetic energy
b.potential energy
c.gravitational potential energy d.mechanical energy
Answer: The answer is D.
Explanation:
The form of energy associated with the motion, position, or shape of an object is called mechanical energy. An object's mechanical energy is a combination of its potential energy and its kinetic energy. The basketball has both potential energy and kinetic energy.
Hope this helps!
I have an object with a density of 0.351g/mL and a volume of 51 mL. What is the mass of this object
Answer:
17.9
Explanation:
to find mass you multiply density and volume. so mass=(51)(0.351) which is 17.901
The solubility of silver(I)phosphate at a given temperature is 2.43 g/L. Calculate the Ksp at this temperature. After you calculate the Kspvalue, take the negative log and enter the (pKsp) value with 2 decimal places.
Answer:
Kps = 3.07 x 10⁻⁸
pKsp= 7.51
Explanation:
First, we calculate the molar solubility of silver(I)phosphate (Ag₃PO₄) from the solubility in g/L by using its molar mass (418.6 g/mol):
2.43 g/L x 1 mol/418.6 g = 5.8 x 10⁻³ mol/L= s
Now, we have to write the ICE chart for the aqueous equilibrium of Ag₃PO₄ as follows:
Ag₃PO₄(g) ⇄ 3 Ag⁺(aq) + PO₄³⁻
I 0 0
C +3s +s
E 3s s
Ksp = [Ag⁺]³[PO₄³⁻]= (3s)³s= 27s⁴
Since s=5.8 x 10⁻³ mol/L, we calculate Ksp:
Ksp= 27(5.8 x 10⁻³ mol/L)⁴= 3.07 x 10⁻⁸
The pKsp value is:
pKsp= - log Ksp = -log (3.07 x 10⁻⁸) = 7.51
Which of the following favors the solubility of an ionic solid in a liquid solvent? Group of answer choices a large magnitude of the solvation energy of the ions a small magnitude of the lattice energy of the solute a large polarity of the solvent all of the above none of the above
Answer:
all of the above
Explanation:
The solubility of an ionic solid in a liquid solvent largely depends on three factors:
i) The solvation energy
ii) The lattice energy of the solid
iii) The polarity of the of the solvent
A large solvation energy and a small magnitude of lattice energy means that the ionic solute will dissolve very easily in the solvent.
Secondly, the solvent must have a large polarity, this is why water serves as a good solvent for most ionic solutes.
What is the atomic mass of element X
Answer:
Which one of the table is element X?
Explanation:
I have no idea and help!!!!!!!!!!!!!!!!!!!!!!!!!
calculate the amount of water produced by the combustion of 16 gram of methane
Answer: Since, the given weight of methane is 16 g, hence the water produced by the combustion of 16 g of methane is 36 g.
Explanation: Have a blessed day!
Hereditary information is passed on from:
O nucleus to nucleus
O cell to cell
O cell to nucleus
O nucleus to cell
Answer:
D - Nucleus to Cell
Explanation:
Hope it helps!!
:D
Which of the following are decomposers?
O A. mice
O B. snakes
O C. fungi
OD. spiders
ASAP
________ and ________ fibres are obtained from animals
Answer:
Explanation:
Silk and wool
Answer:
silk and wool fibers are obtained from animals
Explanation:
good luck :)
What are two weather factors that are directly influenced by ocean currents
O Air density and humidity
O Air pressure and temperature
O Temperature and humidity
O Precipitation and air pressure
Explanation:
Preciptation and air pressure
Answer:
It is Temperature and humidity. C
Explanation:
I took the test and it said it was C
The smallest form of matter that still retains the properties of an element
Answer:
atom
Explanation:
the atom is the smallest form.
Determine the value of the equilibrium constant (report your answer to three significant figures) for the following reaction if an equilibrium mixture contains 0.010 mol of solid PbBr2, and is 0.0100 M in Pb2+ ions and 0.0250 M in Br1- ions. Use the notation 4.31e-5 to indicate a number such as 4.31 x 10-5.
Answer:
6.25e-6 is the value of the equilibrium constant
Explanation:
we have this equation
[tex]PbBr(s) ----- Pb^{2+}(aq) + 2Br(aq)[/tex]
When at a state of equilibrium,
we have the concentration of Pb^2+ to be 0.01
we have the concentration of Br^- to be 0.025
the equilibrium constant concentration of both pure solids and liquid s are said to be equal to 1
[PbBR2] = 1
such tht
Keq = [Pb^2+] x [Br-]^2
we already know the values of these from the above.
0.01x0.025^2
= 0.01 x 0.000625
= 0.00000625
= 6.25 x 10^-6
= 6.25e^-6
a change of matter is a physical change
True or False
Answer:
true
Explanation:
hope it helps
Answer:
I'm pretty sure it's true
Explanation:
20 characters
Which of the following is NOT a strong electrolyte?
:
Answers:
Na2SO4
KI
CaCl2
LiOH
C6H1206
Answer:
C6H1206
Explanation:
C6H12O6 is a monomer of carbohydrates also known as glucose, so it is not an electrolyte at all.
Based on the visible cell structure, which of the following statements is true?
Answer:I think it would be the third one.
Explanation:
What is magma?
solid rock with a fine texture
cooled rock with large crystals
molten rock below Earth’s surface
flowing rock above Earth’s surface
Answer:
C. molten rock below Earth’s surface
Explanation: